You're in. Let's go.

An OBD tracker, a Yipii starter pack leaflet, and a small alignment sticker. The multi-network SIM is already inside the device.

No. Yipii trackers ship with an embedded multi-network SIM that's already inside the device. There's nothing for you to fit, and nothing to lose.

Check your spam or promotions folder first. If it still isn't there, message [email protected] and we'll resend it within the hour.

No. The Yipii IoT app is enough to set up and use your tracker.

Type the IMEI in manually instead. If the label is dusty, give it a quick wipe. Bright, even light helps the camera lock on.

Message [email protected] with your IMEI number and we will sort it. This usually means the device was paired during quality checks and just needs releasing on our side.

The tracker is the physical device. The asset is the thing you care about — a van, a generator, a boat. You assign trackers to assets so the data shows up under the right vehicle on your map.

Yes. Open the tracker in the app, tap "Reassign", and pick the new asset. The history follows the asset, not the device.

Try under the steering column, behind the fuse-box flap, or in the footwell on the driver's side. On vans it can sit near the gear lever. If you still can't spot it, search "[your vehicle make and model] OBD port location" — there's almost always a photo online.

No. The Yipii OBD tracker reads from the port and does not write to the vehicle bus. It is the same kind of connection an insurance dongle or a scan tool uses.

A short drive of three to five minutes is usually enough. The tracker won't post much while parked, so don't expect movement until you're rolling.

Check that the device LED is on, that the ignition was on for the drive, and that you have signal where you parked. If it still looks blank, message support and include the IMEI.

A wired tracker with a U-cable harness (red and black), a Yipii starter pack leaflet, and a few zip ties. The multi-network SIM is already inside the device.

No. Yipii trackers ship with an embedded multi-network SIM that's already inside the device. There's nothing for you to fit, and nothing to lose.

Check your spam or promotions folder first. If it still isn't there, message [email protected] and we'll resend it within the hour.

No. The Yipii IoT app is enough to set up and use your tracker.

Type the IMEI in manually instead. If the label is dusty, give it a quick wipe. Bright, even light helps the camera lock on.

Message [email protected] with your IMEI number and we will sort it. This usually means the device was paired during quality checks and just needs releasing on our side.

The tracker is the physical device. The asset is the thing you care about — a van, a generator, a boat. You assign trackers to assets so the data shows up under the right vehicle on your map.

Yes. Open the tracker in the app, tap "Reassign", and pick the new asset. The history follows the asset, not the device.

For safety, connect the positive (+) first when fitting, and disconnect the negative (–) first if you ever take it off. This avoids any chance of a short against the bodywork.

That's fine. The same principle applies — find the terminals and clip on the U-cables. If access is tight, contact support and we'll talk you through it.

A short drive of three to five minutes is usually enough. The tracker won't post much while parked, so don't expect movement until you're rolling.

Check that the device LED is on, that the ignition was on for the drive, and that you have signal where you parked. If it still looks blank, message support and include the IMEI.

A wired tracker, a Yipii starter kit (wiring loom, connectors, zip ties, labels, printed install guide), and a starter pack leaflet. The multi-network SIM is already inside the device.

No. Yipii trackers ship with an embedded multi-network SIM that's already inside the device. There's nothing for you to fit, and nothing to lose.

Check your spam or promotions folder first. If it still isn't there, message [email protected] and we'll resend it within the hour.

No. The Yipii IoT app is enough to set up and use your tracker.

Type the IMEI in manually instead. If the label is dusty, give it a quick wipe. Bright, even light helps the camera lock on.

Message [email protected] with your IMEI number and we will sort it. This usually means the device was paired during quality checks and just needs releasing on our side.

The tracker is the physical device. The asset is the thing you care about — a van, a generator, a boat. You assign trackers to assets so the data shows up under the right vehicle on your map.

Yes. Open the tracker in the app, tap "Reassign", and pick the new asset. The history follows the asset, not the device.

It taps the ignition line, reads the accessory feed, and is wired in for anti-tamper. None of that is hard for an auto-electrician, but it isn't a plug-and-play job — getting it right first time is worth the half-hour.

Installation isn't included, but we can recommend trusted partners we've worked with before. For larger fleets, talk to us about a bulk install package.

A short drive of three to five minutes is usually enough. The tracker won't post much while parked, so don't expect movement until you're rolling.

Check that the device LED is on, that the ignition was on for the drive, and that you have signal where you parked. If it still looks blank, message support and include the IMEI.